Analisa Cacat Las Pipa Pembakaran Boiler dengan Metode PAUT (Phased Array Ultrasonic Testing)
DOI:
https://doi.org/10.47134/innovative.v3i1.95Keywords:
Analisa, Cacat las pipa pembakaran, Boiler, Phassed Array Ultrasonic TestingAbstract
Analisa ini membahas mengenai pengujian Ultrasonic Testing terhadap lasan pipa pembakaran Boiler. Penelitian Ultrasonic Testing berfungsi untuk mengetahui kecacatan yang terdapat pada bagian lasan. Terdapat rumusan masalah yang akan dibahas oleh peneliti yaitu adakah kecacatan atau porositas pada las pipa saluran pembakaran yang diuji dengan Ultrasonic Testing?. Metode pengujian Ultrasonic Testing menggunakan standar ASME section V article 4 yang digunakan untuk pengujian Ultrasonic Testing menggunakan probe jenis cobra dengan merk Doppler dengan nomer seri QA002FAA078. Pengujian ini dilakukan di PT. Lontar Papyrus Pulp & Paper Industry, Jabung Barat, Jambi. Hasil dari pengujian -+700 pipa saluran pembakaran, penguji hanya mengambil satu contoh yaitu join nomer 28 original dan 28 after repair. Maka hasil dari analisa dapat dikatakan accept atau rejectnya lasan dilihat dari banyak porositas atau kecacatan yang perlu di las ulang.
References
ASME. (2003). ASME Boiler and Pressure Vessel Code. ASME.
Bajgholi, M. E. (2023). Total focusing method applied to probability of detection. International Journal of Advanced Manufacturing Technology, 126(7), 3637–3647. https://doi.org/10.1007/s00170-023-11328-x DOI: https://doi.org/10.1007/s00170-023-11328-x
Bezza, A. (2016). Remarks on Defect Detection in a Two-Dimensional Structure with Welded Joints. HAL.
Castro, E. R. (2024). Weld Qualification of the Cold Mass of the Superconducting Quadrupoles Magnets (MQXF) for the HL-LHC Project. IEEE Transactions on Applied Superconductivity, 34(3), 1–4. https://doi.org/10.1109/TASC.2024.3353137 DOI: https://doi.org/10.1109/TASC.2024.3353137
Debora. (2013). Pengukuran Ketebalan Serta Posisi Cacat pada Sampel Carbon Steel dan Stainless Steel Dengan Metode Ultrasonic Testing.
Ebhota, W. S. (2016). Centrifugal Casting Technique Baseline Knowledge, Applications, and Processing Parameters: Overview. Zeitschrift Für METALLKUNDE. DOI: https://doi.org/10.3139/146.111423
Endramawan, T. (2017). Non Destructive Test Dye Penetrant and Ultrasonic on Welding SMAW Butt Join with Acceptance Criteria ASME Standard. IOP Publishing. DOI: https://doi.org/10.1088/1757-899X/306/1/012122
He, C. (2016). Design and Fabrication of Air-Based 1-3 Piezoelectric Composite Transducer for Air-Coupled Ultrasonic Applications. Hindawi. DOI: https://doi.org/10.1155/2016/4982616
He, Y. (2014). Non-Destructive Testing of Low-Energy Impact in CFRP Laminates and Interior Defects in Honeycomb Sandwich Using Scanning Pulsed Eddy Current. ELSEVIER. DOI: https://doi.org/10.1016/j.compositesb.2013.12.005
Johnson. (2019). How and Why We Need to Capture Tacit Knowledge in Manufacturing: Case. Applied Ergonomics, 1–9. DOI: https://doi.org/10.1016/j.apergo.2018.07.016
Kamaraj, A. B. (2017). Experimental Study on the Porosity of Electrochemical Nickel Deposits. ELSEVIER. DOI: https://doi.org/10.1016/j.promfg.2017.07.032
Kendarnath, G. (2017). Fatigue Surface Crack Detection by Using Fluorescent Dye Penetrant Test Technique on Welded Engineering Service Components. International Research Journal of Engineering and Technology (IRJET).
Kim, Y. H. (2024). Automated data evaluation in phased-array ultrasonic testing based on A-scan and feature training. NDT and E International, 141. https://doi.org/10.1016/j.ndteint.2023.102974 DOI: https://doi.org/10.1016/j.ndteint.2023.102974
Lalitha, G. (2015). Experimental Study on Non-Destructive Testing Techniques (NDTT). International Journal of Engineering Research and General Science.
LUO, Z. (2023). Enhanced ultrasonic total focusing imaging of CFRP corner with ray theory-based homogenization technique. Chinese Journal of Aeronautics, 36(1), 434–443. https://doi.org/10.1016/j.cja.2022.09.010 DOI: https://doi.org/10.1016/j.cja.2022.09.010
Mongja. (2017). Evaluation on Use of Industrial Radiography for Weld Joints Inspection in Tanzania. International Journal of Mechanical Engineering and Technology (IJMET).
NDT. (2015). Guidance Document: An Introduction to NDT Common Methods. Roll-Royce.
Nicolson, E. (2023). Dual-tandem phased array method for imaging of near-vertical defects in narrow-gap welds. NDT and E International, 135. https://doi.org/10.1016/j.ndteint.2023.102808 DOI: https://doi.org/10.1016/j.ndteint.2023.102808
Opačić, M. F. (2024). Risk Assessment of Pressure Vessels by Using Fracture Mechanics and Advanced Ultrasonic Testing. Tehnicki Vjesnik, 31(1), 118–124. https://doi.org/10.17559/TV-20230227000386 DOI: https://doi.org/10.17559/TV-20230227000386
Pahleviannur, M. R. (2022). Penentuan Prioritas Pilar Satuan Pendidikan Aman Bencana (SPAB) menggunakan Metode Analytical Hierarchy Process (AHP). Pena Persada. DOI: https://doi.org/10.31237/osf.io/6ghyz
Pahleviannur, M. R., Ayuni, I. K., Widiastuti, A. S., Umaroh, R., Aisyah, H. R., Afiyah, Z., Azzahra, I., Chairani, M. S., Dhafita, N. A., & Rohmah, N. L. (2023). Kerentanan Sosial Ekonomi terhadap Bencana Banjir di Hilir DAS Citanduy Bagian Barat Kabupaten Pangandaran Jawa Barat. Media Komunikasi Geografi, 24(2), 189–205. DOI: https://doi.org/10.23887/mkg.v24i2.66370
Piao, G. (2023). Phased array ultrasonic imaging and characterization of adhesive bonding between thermoplastic composites aided by machine learning. Nondestructive Testing and Evaluation, 38(3), 500–518. https://doi.org/10.1080/10589759.2022.2134365 DOI: https://doi.org/10.1080/10589759.2022.2134365
Rahman, M. S. U. (2023). Inspection of thick composites: a comparative study between microwaves, X-ray computed tomography and ultrasonic testing. Nondestructive Testing and Evaluation. https://doi.org/10.1080/10589759.2023.2287071 DOI: https://doi.org/10.1080/10589759.2023.2287071
Romanishin, R. I. (2018). Processing of Backscattered Signal in Ultrasonic Testing. Pleiades Publishing, 395–396.
Seo, D. (2023). An Experimental Study on Defect Detection of Anchor Bolts Using Non-Destructive Testing Techniques. Materials, 16(13). https://doi.org/10.3390/ma16134861 DOI: https://doi.org/10.3390/ma16134861
Sharma, A. (2018). Ultrasonic Testing for Mechanical Engineering Domain: Present and Future Perspective. International Journal of Research in Industrial.
Siswanto, R. (2018). Analisis Porositas Panduan AL-12.6% Si Dengan Variasi Waktu Tunggu Dalam Cetakan Dan Media Pendingin Hasil Pengecoran Evaporative. DOI: https://doi.org/10.20527/jukung.v4i1.4663
Sudharsan, P. L. (2024). Multi modal data fusion of PAUT with thermography assisted by Automatic Defect Recognition System (M-ADR) for NDE Applications. NDT and E International, 143. https://doi.org/10.1016/j.ndteint.2024.103062 DOI: https://doi.org/10.1016/j.ndteint.2024.103062
Tiedemann. (2018). Integrating Sensors in Casting Made Aluminum-New Approach for Direct Sensor Integration in Gravity Die Casting. DOI: https://doi.org/10.1016/j.promfg.2018.06.042
Downloads
Published
How to Cite
Issue
Section
License
Copyright (c) 2024 Mochammad Amir Syarifuddin, Ali Akbar
This work is licensed under a Creative Commons Attribution 4.0 International License.
